Cosine can print billets in virtually any shape out of virtually any thermoplastic. 3D printed billets can be significantly cheaper than extruded billets. Cosine can produce short-run batches of billets or even a single part.

 
_MG_6686.jpg
_MG_6701.jpg

PPS (25% carbon fiber - Not machined)

This RAW block of PPS is a cheaper alternative to a machine PPS, but keeps all the same properties such as temperature resistance, strength, chemical resistance and flame retardant.

If you don’t mind your billet having a RAW finish, then this is the billet for you.

PPS (25% carbon fiber - machined)

This PPS is a 25% carbon fiber-filled high-temperature thermoplastic with an exceptional balance of cost, temperature resistance, strength, chemical resistance and flame retardant. PPS is often used when long-term high-temperature performance and dimensional stability are a must, even in the presence of destructive chemicals.

  • PPS 40% Glass Filled

  • Radel ® R5500 PPSU Natural (Bone White)

  • Sustatron PPS

  • TECATRON ® GF40 40% Glass Filled PPS

  • TECATRON ® PPS Unfilled Virgin

  • TECATRON ® PVX PPS

  • Techtron ® HPV PPS

  • Techtron ® PPS Unfilled Virgin

  • Techtron ® PSBG PPS

  • Techtron ® PSGF 40% Glass Filled PPS

  • XP-116 TECAPEEK ® 40% Glass & 20% PPS Filled PEEK

  • XP-170 TECATRON ® EWS Filled PPS

  • XP-61 TECATRON ® 25% Fiberglass & Mineral Filled PPS

  • XP-61L TECATRON ® 25% Fiberglass & Mineral Filled PPS

  • XP-61LT TECATRON ® 25% Fiberglass & Mineral Tested PPS

  • XP-63 TECATRON ® 50% Fiberglass Filled PPS

  • XP-63T TECATRON ® 50% Glass Fiber Filled Black Tested PPS

  • XP-64B TECATRON ® 40% Fiberglass Filled Black PPS

  • XP-64T TECATRON ® 40% Fiberglass Filled Natural Tested PPS

  • XP-65 TECATRON ® 30% Fiberglass & 15% PTFE Filled PPS

  • XP-65B TECATRON ® 30% Fiberglass & 15% PTFE Filled Black PPS

  • XP-65T TECATRON ® 30% Fiberglass & 15% PTFE Filled Tested PPS

  • XP-66 TECATRON ® 30% Fiberglass Filled PPS

  • XP-66B TECATRON ® 30% Fiberglass Filled Black PPS

  • XP-67 TECATRON ® 15% Fiberglass Filled PPS

  • XP-68 TECATRON ® 25% Fiberglass & Graphite Filled PPS

  • XP-69 TECATRON ® 35% Fiberglass & Mineral Filled PPS

  • XP-71 TECATRON ® 20% PTFE Filled PPS

  • XP-72 TECATRON ® 64% PTFE Filled PPS Seal Formulation

  • XP-73 TECATRON ® 60% PTFE Filled PPS Seal Formulation

  • XP-74 TECATRON ® 30% Carbon Fiber & 8% PTFE Filled PPS

  • XP-76 TECATRON ® 55% PTFE Filled PPS Seal Formulation

  • XP-76T TECATRON ® 55% PTFE Filled Tested PPS Seal Formulation

  • XP-78 TECATRON ® 47% PTFE Filled PPS Seal Formulation

  • XP-79 TECATRON ® 70% PTFE Filled PPS Seal Formulation

  • XP-79T TECATRON ® 70% PTFE Filled Tested PPS Seal Formulation

  • XP-81 TECATRON ® 15% Graphite & 15% Carbon Fiber Filled PPS

  • XP-82 TECATRON ® 15% PTFE & 30% Carbon Fiber Filled PPS

  • XP-83 TECATRON ® 10% PTFE, 10% Graphite & 15% Carbon Fiber Filled PPS

  • XP-84 TECATRON ® 30% Graphite Filled PPS

  • XP-85 TECATRON ® 30% Carbon Fiber Filled PPS

  • XP-86 TECATRON ® 40% Carbon Fiber Filled PPS

  • XP-87 TECATRON ® 20% Carbon Fiber Filled PPS

  • XP-88 TECATRON ® 10% Graphite, 15% PTFE & 15% Carbon Fiber Filled PPS

  • XP-89 TECATRON ® 20% Carbon Fiber 10% PTFE & 5% Graphite Filled PPS

_MG_6704.jpg
_MG_6707.jpg

polypropylene

Polypropylene is a cost-effective material that offers a combination of impressive physical, chemical, mechanical, thermal and electrical properties not found in any other thermoplastic. Compared to low or high density polyethylene, it has a low impact strength, but exceptional working temperature with tensile strength.

  • Flametec ® CP-5 Flame Retardant Polypropylene (UL 94 V-0)

  • Foamlite ® P Polypropylene

  • King Polypropylene

  • Polypropylene PP Copolymer

  • Polypropylene PP Homopolymer

  • Polypropylene PP Natural

  • Polystone ® P Copolymer Polypropylene

  • Polystone ® P Homopolymer Polypropylene

  • Polystone ® P MG Medical Grade (Polypropylene-Heat Stabilized)

  • Propylux ® CN-F Conductive Polypropylene

  • Propylux ® CN-P Conductive Polypropylene

  • Propylux ® HS (Polypropylene-Heat Stabilized)

  • Propylux ® HS2 (Polypropylene-Heat Stabilized)

  • Propylux ® SD-A (Anti-Static Polypropylene)

  • PROTEUS ® LF Polypropylene

  • Proteus ® LSG Life Science Grade (Polypropylene-Heat Stabilized)

  • Proteus ® PP Natural Co-Polymer Polypropylene

  • Proteus ® PP Natural Homopolymer Polypropylene

  • Proteus ® PP Natural O & P Homopolymer Polypropylene

  • Proteus ® PP White Homopolymer Polypropylene

  • TECAPRO ® Standard Polypropylene (copolymer)

_MG_7000_JPG.jpg

PEKK (Poly-ether-ketone-ketone)

PEKK is among one of the highest performing polymers on the market. It is lightweight, strong, and offers phenomenal resistance to intense environments such as oil exploration and aerospace. If you are planning on putting your print under severe situations, this is the perfect material for you.

  • 3DXSTAT™ ESD-PEKK

  • CarbonX™ Carbon Fiber PEKK (Aerospace)

  • CarbonX™ Carbon Fiber PEKK (Industrial)

  • Celazole ® TK-60 Unfilled PBI PEKK

  • Celazole ® TK-60C Carbon Filled PBI PEKK

  • Celazole ® TKL-60 Lubricated PBI PEKK

  • ThermaX™ HTS High-Temp Support

  • ThermaX® PEKK

  • … and MORE!

peek

PEEK is a colorless, organic thermoplastic polymer that achieves some of the best results out of all thermoplastics worldwide.

It has high impact strength, durability, heat resistance, chemical resistance, and it is flame retardant.

  • Celazole ® TF-60C Carbon Filled PBI PEEK

  • Celazole ® TF-60V Glass Filled PBI PEEK

  • Celazole ® TL-60 Lubricated PBI PEEK

  • Celazole ® TU-60 Unfilled PBI PEEK

  • EPM-2204U-W Ceramic-Filled PEEK

  • Ketron ® 1000 Unfilled Virgin PEEK

  • Ketron ® CA30 PEEK

  • Ketron ® CLASSIX ™ LSG PEEK

  • Ketron ® CM CA30 PEEK

  • Ketron ® CM GF30 PEEK

  • Ketron ® CM HPV PEEK

  • Ketron ® GF30 PEEK

  • Ketron ® HPV PEEK

  • Ketron ® PEEK CA30 LSG

  • Ketron ® PEEK GF30 LSG

  • Ketron ® PEEK LSG

  • Ketron ® TX PEEK

  • Krefine ® ESD PEEK EKH SS07 (10^6 - 10^8 Ohm/Square)

  • PEEK Bearing Grade

  • PEEK CA30 - 30% Carbon Filled

  • PEEK GF30 - 30% Glass Filled

  • PEEK HT ™

  • PEEK Unfilled Virgin Natural

  • Semitron ® ESd 480 PEEK

  • Semitron ® ESd 490 HR PEEK

  • Semitron ® ESd HPV PEEK

  • Semitron ® MDS 100 PEEK

  • Semitron ® MP 370 PEEK

  • SustaPEEK

  • SustaPEEK CF 30

  • SustaPEEK GF 30

  • SustaPEEK MG (Medical Grade) PEEK

  • SustaPEEK XDT X Ray Detectable PEEK

  • TECAPEEK ® ELS nano

  • TECAPEEK ® GF30 30% Glass Filled PEEK

  • TECAPEEK ® ID Metal Detectable PEEK

  • TECAPEEK ® MT

  • TECAPEEK ® MT CF30

  • TECAPEEK ® MT CLASSIX ™

  • TECAPEEK ® MT XP98

  • TECAPEEK ® MT XP98 XRO X-Ray Opaque

  • TECAPEEK ® TS (Test Socket Grade)

  • TECAPEEK ® UD Blue Ultra Detectable PEEK

  • TECAPEEK ® Unfilled Virgin PEEK

  • XP-100 TECAPEEK ® 10% Graphite, 10% PTFE & 10% Carbon Filled PEEK

  • XP-101 TECAPEEK ® 15% Graphite & 10% PTFE Filled PEEK

  • XP-102 TECAPEEK ® 5% PTFE FIlled PEEK

  • XP-103 TECAPEEK ® 15% Carbon Fiber Filled PEEK

  • XP-104 TECAPEEK ® 7% Moly, 3% PTFE & 25% Carbon Filled PEEK

  • XP-105 TECAPEEK ® 15% Graphite Filled PEEK

  • XP-106 TECAPEEK ® 40% Fiberglass Filled PEEK

  • XP-107 TECAPEEK ® 25% Carbon Fiber Filled PEEK

  • XP-108 TECAPEEK ® 20% PTFE Filled PEEK

  • XP-109 TECAPEEK ® 30% Carbon & 15% PTFE Filled PEEK

  • XP-110 TECAPEEK ® 45% Mineral Filled PEEK

  • XP-111 TECAPEEK ® 50% Carbon Fiber Filled PEEK

  • XP-112 TECAPEEK ® 20% Carbon Fiber Filled PEEK

  • XP-113 TECAPEEK ® 10% PTFE, 15% Graphite & 3% Carbon Filled PEEK

  • XP-114 TECAPEEK ® 40% Carbon Fiber Filled PEEK

  • XP-115 TECAPEEK ® Static Dissipative PEEK

  • XP-115B TECAPEEK ® Static Dissipative Black PEEK

  • XP-116 TECAPEEK ® 40% Glass & 20% PPS Filled PEEK

  • XP-117 TECAPEEK ® 25% PTFE Filled PEEK

  • XP-118 TECAPEEK ® 20% Fiberglass & 5% PTFE Filled PEEK

  • XP-119 TECAPEEK ® 10% Carbon Fiber Filled PEEK

  • XP-119G TECAPEEK ® 10% Carbon Fiber & 5% Graphite Filled PEEK

  • XP-181 TECAPEEK EWS & Carbon Fiber Filled PEEK

  • XP-280 TECAPEEK ® 30% Carbon Fiber Filled PBI PEEK

  • XP-90 TECAPEEK ® 25% Fiberglass Filled PEEK

  • XP-91 TECAPEEK ® 30% Fiberglass Filled PEEK

  • XP-91B TECAPEEK ® 30% Glass Filled Black PEEK

  • XP-91BHT TECAPEEK ® BHT Glass Filled High Temp Black PEEK

  • XP-91T TECAPEEK ® 30% Glass Filled Natural Tested PEEK

  • XP-92 TECAPEEK ® 15% Fiberglass Filled PEEK

  • XP-93 TECAPEEK ® 30% PTFE Filled PEEK

  • XP-93G TECAPEEK ® 30% PTFE & 5% Graphite Filled PEEK

  • XP-94 TECAPEEK ® 20% Fiberglass Filled PEEK

  • XP-94B TECAPEEK ® 20% Glass Filled Black PEEK

  • XP-95 TECAPEEK ® 15% PTFE Filled PEEK

  • XP-96 TECAPEEK ® Unfilled Natural PEEK

  • XP-96B TECAPEEK ® Unfilled Black PEEK

  • XP-96BHT TECAPEEK ® BHT Unfilled Black High Temp PEEK

  • XP-96T TECAPEEK ® Unfilled Natural Tested PEEK

  • XP-97 TECAPEEK ® 30% Graphite Filled PEEK

  • XP-98 TECAPEEK ® 30% Carbon Fiber Filled PEEK

  • XP-98HT TECAPEEK ® 30% Carbon Fiber High Temp PEEK

  • XP-98Med TECAPEEK ® CF Medical Device Grade PEEK

  • XP-99 TECAPEEK ® 7% Graphite, 8% PTFE & 15% Carbon Filled PEEK

  • XP-99T TECAPEEK ® 7% Graphite, 8% PTFE & 15% Carbon Filled Tested PEEK

  • ZL ® 1500 PEEK

  • ZL ® 1500 X PEEK

 

Our 3D printed billets are better than hot molded plastics. We could achieve a 27% increase in tensile strength and 36% in tensile strain.

Cosine can also provide machining services if you’re looking for a finalized part rather than rough material.

Web Analytics